[Jul 17, 2025] Get Unlimited Access to NSE7_PBC-7.2 Certification Exam Cert Guide
Reliable Study Materials for NSE7_PBC-7.2 Exam Success For Sure
Fortinet NSE7_PBC-7.2 certification exam is designed to test the knowledge and skills of professionals in public cloud security. Fortinet NSE 7 - Public Cloud Security 7.2 certification is highly valued in the IT industry, as it provides evidence of expertise in securing public cloud environments. NSE7_PBC-7.2 exam covers a range of topics, including cloud security fundamentals, cloud-specific threats and vulnerabilities, as well as advanced cloud security techniques.
Fortinet NSE7_PBC-7.2 is an exam offered by Fortinet for individuals aiming to validate their skills and knowledge in public cloud security. NSE7_PBC-7.2 exam is designed to test the candidate's ability to configure, maintain, and troubleshoot Fortinet's public cloud security solutions.
NEW QUESTION # 20
You need to deploy FortiGate VM devices in a highly available topology in the Microsoft Azure cloud. The following are the requirements of your deployment:
- Two FortiGate devices must be deployed; each in a different availability zone.
- Each FortiGate requires two virtual network interfaces: one will connect to a public subnet and the other will connect to a private subnet.
- An external Microsoft Azure load balancer will distribute ingress traffic to both FortiGate devices in an active- active topology.
- An internal Microsoft Azure load balancer will distribute egress traffic from protected virtual machines to both FortiGate devices in an active-active topology.
- Traffic should be accepted or denied by a firewall policy in the same way by either FortiGate device in this topology.
Which FortiOS CLI configuration can help reduce the administrative effort required to maintain the FortiGate devices, by synchronizing firewall policy and object configuration between the FortiGate devices?
- A. config system sdn-connector
- B. config system auto-scale
- C. config system ha
- D. config system session-sync
Answer: C
Explanation:
FTG HA Active/Active requires the following configuration to sync the session by FGSP config system ha set session-pickup enable set session-pickup-connectionless enable set session-pickup-nat enable set session-pickup-expectation enable set override disable end config system cluster-sync edit 0 set peerip 10.0.1.x set syncvd "root" next end
NEW QUESTION # 21
Refer to Exhibit. You are troubleshooting a Microsoft Azure SDN connector issue on your FortiGate VM in Azure.
Which three settings should you check while troubleshooting this problem? (Choose three.)
- A. Ensure FortiGate port4 can resolve DNS.
- B. Use the show vdom command to see hidden VDOMs.
- C. Ensure IP address 169.254.169.254 is not blocked
- D. use the diag sys va command.
- E. Ensure FortiGate port1 has internet access
Answer: A,C,E
Explanation:
The three settings that should be checked while troubleshooting this problem are:
- Ensure FortiGate port4 can resolve DNS. This is because the Azure SDN connector requires DNS resolution to communicate with the Azure API. If the FortiGate port4 cannot resolve DNS, the SDN connector will not be able to retrieve the Azure resources and display them in the GUI.
- Ensure FortiGate portl has internet access. This is because the Azure SDN connector requires internet access to communicate with the Azure API. If the FortiGate portl does not have internet access, the SDN connector will not be able to connect to the Azure cloud and display an error in the CLI.
- Ensure IP address 169.254.169.254 is not blocked. This is because the Azure SDN connector uses this IP address to obtain metadata information from the Azure instance. If this IP address is blocked by a firewall policy or a network ACL, the SDN connector will not be able to get the required information and display an error in the CLI.
NEW QUESTION # 22
Refer to the exhibit.
You deployed an HA active-active load balance sandwich with two FortiGate VMs in Microsoft Azure.
After the deployment, you prefer to use FGSP to synchronize sessions, and allow asymmetric return traffic In the environment, FortiGate port 1 and port 2 are facing external and internal load balancers respectively What IP address must you use in the peerip configuration?
- A. The internal load balancer port 1 IP address.
- B. The opposite FortiGate port 2 IP address.
- C. The opposite FortiGate port 1 IP address.
- D. The public load balancer port 2 IP address
Answer: B
Explanation:
HA Synchronization Requirements: FGSP requires direct communication between the FortiGates to synchronize the session table. This synchronization typically occurs over a dedicated HA link that connects the HA pair.
Asymmetric Traffic Considerations: FGSP allows asymmetric traffic to rejoin the correct session by synchronizing session information, including NAT and TCP sequence tracking between the FortiGate units in a cluster.
Configuration Specifics: For port 2, which is facing the internal load balancer, the peerip should be set to the corresponding port 2 IP address of the opposite FortiGate. This allows the internal interfaces to communicate directly with each other for session synchronization purposes, which is crucial in an active-active deployment to ensure sessions persist during failover scenarios.
Explanation:
In an HA active-active load balance configuration with FortiGate VMs, especially in Microsoft Azure where FGSP (FortiGate Session Life Support Protocol) is used for session synchronization, the correct configuration for the peerip is:
NEW QUESTION # 23
You are tasked with deploying a FortiGate HA solution in Amazon Web Services (AWS) using Terraform What are two steps you must take to complete this deployment? (Choose two.)
- A. Create an AWS Active Directory user with permissions.
- B. Create an AWS Identity and Access Management (IAM) user With permissions.
- C. Use CloudSheIl to install Terraform.
- D. Enable automation on the AWS portal.
Answer: B,C
Explanation:
To deploy a FortiGate HA solution in AWS using Terraform, you need to create an AWS IAM user with permissions to access the AWS resources and services required by the FortiGate-VM. You also need to use CloudShell to install Terraform, which is a tool for building, changing, and versioning infrastructure as code.
Reference:
Deploying FortiGate-VM using Terraform | AWS Administration Guide
Setting up IAM roles | AWS Administration Guide
Launching the instance using roles and user data | AWS Administration Guide Terraform by HashiCorp
NEW QUESTION # 24
You are asked to find a solution to replace the existing VPC peering topology to have a higher bandwidth connection from Amazon Web Services (AWS) to the on-premises data center.
Which two solutions will satisfy the requirement? (Choose two.)
- A. Use the transit gateway attachment With VPN option to create multiple VPN connections to the on-premises data center
- B. Use transit VPC to build multiple VPC connections to the on-premises data center
- C. Use a transit VPC with hub and spoke topology to create multiple VPN connections to the on- premises data center.
- D. Use ECMP and VPN to achieve higher bandwidth.
Answer: A,C
Explanation:
Use a transit VPC with hub and spoke topology to create multiple VPN connections to the on- premises data center. Use the transit gateway attachment with VPN option to create multiple VPN connections to the on-premises data center. According to the Fortinet documentation for Public Cloud Security, a transit VPC is a VPC that serves as a global network transit center for connecting multiple VPCs, remote networks, and virtual private networks (VPNs). A transit VPC can use a hub and spoke topology to create multiple VPN connections to the on-premises data center, using the FortiGate VM as a virtual appliance that provides network security and threat prevention. A transit VPC can also leverage Equal-Cost Multi-Path (ECMP) routing to achieve higher bandwidth and load balancing across multiple VPN tunnels. A transit gateway is a network transit hub that connects VPCs and on-premises networks. A transit gateway attachment is a resource that connects a VPC or VPN to a transit gateway. You can use the transit gateway attachment with VPN option to create multiple VPN connections to the on-premises data center, using the FortiGate VM as a virtual appliance that provides network security and threat prevention. A transit gateway attachment with VPN option can also leverage ECMP routing to achieve higher bandwidth and load balancing across multiple VPN tunnels.
NEW QUESTION # 25
Refer to the exhibit. You are deploying two FortiGate VMS in HA active-passive mode with load balancers in Microsoft Azure.
Which two statements are true in this load balancing scenario? (Choose two.)
- A. A dedicated management interface can be used for load balancing.
- B. The FortiGate public IP is the next-hop for all the traffic.
- C. You must add a route to the Microsoft VIP used for the health check.
- D. An internal load balancer listener is the next-hop for outgoing traffic.
Answer: A,D
Explanation:
A is incorrect because the FortiGate public IP is not the next-hop for all the traffic. The FortiGate public IP is only used for incoming traffic from the internet. The Azure load balancer distributes the incoming traffic to the active FortiGate VM based on a health probe. The FortiGate public IP is not used for outgoing traffic or internal traffic.
B is correct because an internal load balancer listener is the next-hop for outgoing traffic. The internal load balancer listener is configured with a floating IP address that is assigned to the active FortiGate VM. The internal load balancer listener also has a health probe to monitor the status of the FortiGate VMs. The internal load balancer listener forwards the outgoing traffic to the internet through the public load balancer.
C is incorrect because you do not need to add a route to the Microsoft VIP used for the health check. The Microsoft VIP is an internal IP address that is used by the Azure load balancer to send health probes to the FortiGate VMs. The Microsoft VIP is not reachable from outside the Azure network and does not require any routing configuration on the FortiGate VMs.
D is correct because a dedicated management interface can be used for load balancing. In this deployment, port is used as a dedicated management interface that connects to the management network. The dedicated management interface can be used to access the FortiGate VMs for configuration and monitoring purposes. The dedicated management interface can also be used to synchronize the configuration and session information between the primary and secondary devices in an HA cluster.
NEW QUESTION # 26
Your goal is to deploy resources in multiple places and regions in the public cloud using Terraform.
What is the most efficient way to deploy resources without changing much of the Terraform code?
- A. Use the variable, tf file and edit its values to match multiple resources
- B. Install and configure two Terraform staging servers to deploy resources.
- C. Use the provider. tf file to add all the new values
- D. Use multiple terraform.tfvars files With a variables.tf file.
Answer: D
Explanation:
When deploying resources in multiple places and regions in the public cloud using Terraform, the most efficient way is:
A . Use multiple terraform.tfvars files with a variables.tf file.
Terraform.tfvars File: This file is used to assign values to variables defined in your Terraform configuration. By having multiple .tfvars files, you can define different sets of values for different deployments, such as for different regions or environments, without changing the main configuration.
Variables.tf File: This file contains the definition of variables that will be used within your Terraform configuration. It works in conjunction with terraform.tfvars files, allowing you to parameterize your configuration so that you can deploy the same template in multiple environments with different variables.
NEW QUESTION # 27
Refer to the exhibit. You are configuring a second route table on a Transit Gateway to accommodate east-west traffic inspection between two VPCs. However, you are getting an error during the transit gateway route table association with the Connect attachment.
Which action Should you take to fulfill your requirement?
- A. In the second route table: create a propagation with the Connect attachment.
- B. Add both Associations and Propagations in the second TGW route table.
- C. Add a static route in the Routes section
- D. Delete the both Connect and Transport attachments from the first TGW route table
Answer: A
Explanation:
The error message indicates that the Connect attachment is already associated with another transit gateway route table. You cannot associate the same attachment with more than one route table. However, you can propagate the same attachment to multiple route tables. Therefore, to fulfill your requirement of configuring a second route table for east-west traffic inspection between two VPCs, you need to create a propagation with the Connect attachment in the second route table. This will allow the second route table to learn the routes from the Connect attachment and forward the traffic to the security VPC. You also need to associate the second route table with the Transport attachment, which is the transit gateway attachment for the security VPC.
NEW QUESTION # 28
Refer to the exhibit
You are deploying two FortiGate VMS in HA active-passive mode with load balancers in Microsoft Azure Which two statements are true in this load balancing scenario? (Choose two.)
- A. You must add a route to the Microsoft VIP used for the health check.
- B. The FortiGate public IP is the next-hop for all the traffic.
- C. A dedicated management interface can be used for load balancing.
- D. An internal load balancer listener is the next-hop for outgoing traffic.
Answer: A,D
Explanation:
A is incorrect because the FortiGate public IP is not the next-hop for all the traffic. The FortiGate public IP is only used for incoming traffic from the internet. The Azure load balancer distributes the incoming traffic to the active FortiGate VM based on a health probe123. The FortiGate public IP is not used for outgoing traffic or internal traffic.
B is correct because an internal load balancer listener is the next-hop for outgoing traffic. The internal load balancer listener is configured with a floating IP address that is assigned to the active FortiGate VM. The internal load balancer listener also has a health probe to monitor the status of the FortiGate VMs123. The internal load balancer listener forwards the outgoing traffic to the internet through the public load balancer.
C is incorrect because you do not need to add a route to the Microsoft VIP used for the health check. The Microsoft VIP is an internal IP address that is used by the Azure load balancer to send health probes to the FortiGate VMs123. The Microsoft VIP is not reachable from outside the Azure network and does not require any routing configuration on the FortiGate VMs.
D is correct because a dedicated management interface can be used for load balancing. In this deployment, port4 is used as a dedicated management interface that connects to the management network3. The dedicated management interface can be used to access the FortiGate VMs for configuration and monitoring purposes. The dedicated management interface can also be used to synchronize the configuration and session information between the primary and secondary devices in an HA cluster2.
NEW QUESTION # 29
In an SD-WAN TGW Connect topology, which three initial steps are mandatory when routing traffic from a spoke VPC to a security VPC through a Transit Gateway? (Choose three.)
- A. From the security VPC TGW subnet routing table: point 0.0.0.0/0 traffic to theFortiGate internal port
- B. From the security VPC FortiGate internal subnet routing table, point 0.0.0.0/0 traffic to the TGW
- C. From the spoke VPC internal routing table, point 0.0.0.0/0 traffic to the TGW
- D. From the security VPC TGW subnet routing table: point 0.0.0.0/0 traffic to the TGW
- E. From both spoke VPCs and the security VPC, point 0.0.0.0/0 traffic to the Internet Gateway
Answer: A,B,C
Explanation:
* Spoke VPC Routing: The 0.0.0.0/0 (default) route in the spoke VPC must point to the Transit Gateway attachment for traffic to reach other VPCs or external destinations.
* Security VPC Routing: Traffic from the security VPC needs to pass through the FortiGate for inspection and security controls. Therefore, the 0.0.0.0/0 route in the security VPC's TGW subnet routing table must point to the FortiGate's internal port.
* FortiGate Routing: The FortiGate's internal subnet must have its 0.0.0.0/0 route configured to point to the Transit Gateway attachment, allowing traffic to be returned to other VPCs or reach the internet.
In an SD-WAN TGW Connect topology, when routing traffic from a spoke VPC to a security VPC through a Transit Gateway, the mandatory initial steps include:
* From the spoke VPC internal routing table, point 0.0.0.0/0 traffic to the TGW (Option A):This step is crucial for ensuring that all traffic from the spoke VPC destined for external networks is directed through the Transit Gateway, allowing for centralized management and security inspection.
* From the security VPC TGW subnet routing table: point 0.0.0.0/0 traffic to the FortiGate internal port (Option B):Routing all traffic from the TGW subnet in the security VPC to the FortiGate's internal port ensures that traffic is subjected to the necessary security policies and inspections provided by the FortiGate appliance before it proceeds to other destinations or returns to the spoke VPCs.
* From the security VPC FortiGate internal subnet routing table, point 0.0.0.0/0 traffic to the TGW (Option D):This configuration ensures that traffic returning from the security processes handled by the FortiGate is routed back through the Transit Gateway, maintaining the integrity of the secure transit path and ensuring proper routing back to the originating spoke or onward to the internet.
References:These steps align with best practices for implementing SD-WAN solutions in a cloud environment, ensuring that all traffic is appropriately routed through security appliances for necessary controls and monitoring, asdetailed in the Fortinet SD-WAN documentation and AWS Transit Gateway connectivity guidelines.
NEW QUESTION # 30
Refer to the exhibit
The exhibit shows a customer deployment of two Linux instances and their main routing table in Amazon Web Services (AWS). The customer also created a Transit Gateway (TGW) and two attachments Which two steps are required to route traffic from Linux instances to the TGWQ (Choose two.)
- A. In the main subnet routing table in VPC A and B, add a new route with destination 0_0.0.0/0, next hop Internet gateway(IGW).
- B. In the TGW route table, add route propagation to 192.168.0 0/16
- C. In the TGW route table, associate two attachments.
- D. In the main subnet routing table in VPC A and B, add a new route with destination 0_0.0.0/0, next hop TGW.
Answer: C,D
Explanation:
According to the AWS documentation for Transit Gateway, a Transit Gateway is a network transit hub that connects VPCs and on-premises networks. To route traffic from Linux instances to the TGW, you need to do the following steps:
* In the TGW route table, associate two attachments. An attachment is a resource that connects a VPC or VPN to a Transit Gateway. By associating the attachments to the TGW route table, you enable the TGW to route traffic between the VPCs and the VPN.
* In the main subnet routing table in VPC A and B, add a new route with destination 0_0.0.0/0, next hop TGW. This route directs all traffic from the Linux instances to the TGW, which can then forward it to the appropriate destination based on the TGW route table.
The other options are incorrect because:
* In the TGW route table, adding route propagation to 192.168.0 0/16 is not necessary, as this is already the default route for the TGW. Route propagation allows you to automatically propagate routes from your VPC or VPN to your TGW route table.
* In the main subnet routing table in VPC A and B, adding a new route with destination 0_0.0.0/0, next hop Internet gateway (IGW) is not correct, as this would bypass the TGW and send all traffic directly to the internet. An IGW is a VPC component that enables communication between instances in your VPC and the internet.
[Transit Gateways - Amazon Virtual Private Cloud]
NEW QUESTION # 31
Refer to Exhibit. After the initial Terraform configuration in Microsoft Azure, the terraform plan command is run.
Which two statements about running the plan command are true? (Choose two.)
- A. The terraform plan command will deploy the rest of the resources except the service principle details.
- B. You cannot run the terraform apply command before the terraform plan command.
- C. The terraform plan command makes terraform do a dry run.
- D. You must run the terraform init command once, before the terraform plan command
Answer: C,D
Explanation:
A is incorrect because the terraform plan command will not deploy any resources at all. It will only show the changes that would be made if the terraform apply command was run. The error message in the exhibit indicates that the service principal details are invalid, which means that Terraform cannot authenticate to Azure and cannot create any resources.
B is incorrect because you can run the terraform apply command without running the terraform plan command first. The terraform apply command will automatically generate a new plan and prompt you to approve it before applying it. However, running the terraform plan command first can help you preview the changes and avoid any unwanted or unexpected actions.
C is correct because you must run the terraform init command once before the terraform plan command. The terraform init command initializes a working directory containing Terraform configuration files. It downloads and installs the provider plugins required for your configuration, such as the Azure provider. It also creates a hidden directory called .terraform to store the plugin binaries and other metadata. Without running the terraform init command, the terraform plan command will fail because it cannot find the required plugins or modules.
D is correct because the terraform plan command makes Terraform do a dry run. A dry run is a simulation of what would happen if you executed a certain action, without actually performing it.
The terraform plan command creates an execution plan, which is a description of the actions that Terraform would take to make your infrastructure match your configuration. The execution plan shows you what resources will be created, modified, or destroyed, and what attributes will be changed. The execution plan does not affect your infrastructure or state file until you apply it with the terraform apply command.
NEW QUESTION # 32
What is the bandwidth limitation of an Amazon Web Services (AWS) transit gateway VPC attachment?
- A. Up to 1 Gbps per attachment
- B. Up to 50 Gbps per attachment
- C. Up to 10 Gbps per attachment
- D. Up to 1.25 Gbps per attachment
Answer: B
NEW QUESTION # 33
What are three important steps required to get Terraform ready using Microsoft Azure Cloud Shell? (Choose three.)
- A. Move the Terraform file to the bin directory.
- B. Use the wget (te=aform vession) command to upload Terraform.
- C. use the -O command to download Terraform.
- D. Set up a storage account in Azure.
- E. Subscribe to Terraform in Azure.
Answer: A,B,D
Explanation:
To get Terraform ready using Microsoft Azure Cloud Shell, you need to perform the following steps:
Set up a storage account in Azure. This is required to store the Terraform state file in a blob container, which enables collaboration and persistence of the infrastructure configuration1.
Use the wget (terraform_version) command to upload Terraform. This command downloads the latest version of Terraform from the official website and saves it as a zip file in the current directory2.
Move the Terraform file to the bin directory. This step extracts the Terraform executable from the zip file and moves it to the bin directory, which is part of the PATH environment variable. This allows you to run Terraform commands from any directory in Cloud Shell2.
The other options are incorrect because:
You do not need to use the -O command to download Terraform. This command is used to specify a different output file name for the downloaded file, but it is not necessary for this task3.
You do not need to subscribe to Terraform in Azure. Terraform is an open-source tool that can be used with any cloud provider, and there is no subscription or registration required to use it with Azure4. Reference:
Updating the route table and adding an IAM policy
Configure Terraform in Azure Cloud Shell with Bash
wget(1) - Linux man page
Terraform by HashiCorp
NEW QUESTION # 34
Refer to the exhibit. What would be the impact of confirming to delete all the resources in Terraform?
- A. It destroys all the resources in the state file.
- B. It destroys all the resources in the resource group
- C. It destroys all the resources tied to the AWS Identity and Access Management (1AM) user.
- D. It destroys all the resources in the . tfvars file
Answer: A
Explanation:
Confirming to delete all the resources in Terraform will have the following impact: D. It destroys all the resources in the state file.
Terraform State File Role: The terraform.tfstate file contains a real-time mapping of the resources that Terraform manages, including their current configuration and relationships. This file tracks the actual state of resources provisioned by Terraform.
Impact of Destruction: When Terraform prompts for confirmation to destroy resources, and 'yes' is entered, Terraform reads the state file and systematically removes all the resources that are managed as part of that state. This is not limited to a specific .tfvars file, IAM user, or resource group--it is a global action that affects all resources tracked by the state file associated with the current Terraform workspace and configuration.
NEW QUESTION # 35
Refer to the exhibit
You attempted to access the Linux1 EC2 instance directly from the internet using its public IP address in AWS.
However, your connection is not successful.
Given the network topology, what can be the issue?
- A. There is no connection between VPC A and VPC B.
- B. There is no elastic IP address attached to FortiGate in the Security VPC.
- C. The Transit Gateway BGP IP address is incorrect.
- D. There is no internet gateway attached to the Spoke VPC A.
Answer: D
Explanation:
Explanation
This is because the Linux1 EC2 instance is not accessible directly from the internet using its public IP address in AWS.
An internet gateway is a horizontally scaled, redundant, and highly available VPC component that allows communication between instances in your VPC and the internet. Without an internet gateway, the Linux1 EC2 instance cannotreceive or send traffic to or from the internet, even if it has a public IP address assigned to it.
To fix this issue, you need to attach an internet gateway to the Spoke VPC A and configure a route table that directs internet-bound traffic to the internet gateway. You also need to ensure that the Linux1 EC2 instance has a security group that allows inbound and outbound traffic on the desired ports.
[Internet Gateways - Amazon Virtual Private Cloud] : [Attach an Internet Gateway to Your VPC - Amazon Virtual Private Cloud] : [Security Groups for Your VPC - Amazon Virtual Private Cloud]
NEW QUESTION # 36
A customer would like to use FortiGate fabric integration With FortiCNP When configuring a FortiGate VM to add to FortiCNP, which three mandatory configuration steps must you follow on FortiGate? (Choose three.)
- A. Create and IPS sensor and a firewall policy
- B. Enable two-factor authentication.
- C. Create an SSL]SSH inspection profile.
- D. Create an IPsec tunnel.
- E. Enable send logs-
Answer: A,C,E
Explanation:
Explanation
To configure a FortiGate VM to add to FortiCNP, you need to perform three steps on FortiGate:
Enable send logs in FortiGate to allow FortiCNP to receive the IPS logs from FortiGate.
Create an SSL/SSH inspection profile on FortiGate to inspect the encrypted traffic and apply IPS protection.
Create an IPS sensor and a firewall policy on FortiGate to enable IPS detection and prevention for the traffic.
References:
FortiCNP 22.4.a Administration Guide, page 22-24
FortiGate IPS Administration Guide, page 9-10
NEW QUESTION # 37
A customer would like to use FortiGate fabric integration With FortiCNP When configuring a FortiGate VM to add to FortiCNP, which three mandatory configuration steps must you follow on FortiGate? (Choose three.)
- A. Create and IPS sensor and a firewall policy
- B. Enable two-factor authentication.
- C. Create an SSL]SSH inspection profile.
- D. Create an IPsec tunnel.
- E. Enable send logs-
Answer: A,C,E
Explanation:
To configure a FortiGate VM to add to FortiCNP, you need to perform three steps on FortiGate:
* Enable send logs in FortiGate to allow FortiCNP to receive the IPS logs from FortiGate.
* Create an SSL/SSH inspection profile on FortiGate to inspect the encrypted traffic and apply IPS protection.
* Create an IPS sensor and a firewall policy on FortiGate to enable IPS detection and prevention for the traffic.
References:
* FortiCNP 22.4.a Administration Guide, page 22-24
* FortiGate IPS Administration Guide, page 9-10
NEW QUESTION # 38
......
New Fortinet NSE7_PBC-7.2 Dumps & Questions: https://www.practicematerial.com/NSE7_PBC-7.2-exam-materials.html
100% Latest Most updated NSE7_PBC-7.2 Questions and Answers: https://drive.google.com/open?id=1_T8gDALQ0pS9lVJfk_jKi4IexfDukLZC
