[Nov 28, 2021] Pass NACE NACE-CIP1-001 Exam Info and Free Practice Test
NACE-CIP1-001 Exam Dumps PDF Updated Dump from PracticeMaterial Guaranteed Success
NEW QUESTION 27
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To dissolve the resin
- C. To promote faster cure
- D. To control the evaporation rate
Answer: D
NEW QUESTION 28
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Permit coating to take place so as not to lose the blast
- C. Review the relevant standard with the Contractor
- D. Call your supervisor
Answer: C
NEW QUESTION 29
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Inspectors position is not the majority position
- C. The Inspector is convinced by verifiable facts
- D. The Owner can save some money by the change
Answer: C
NEW QUESTION 30
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. holiday.
- B. cracking.
- C. checking.
- D. sagging.
Answer: A
NEW QUESTION 31
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The inspection cost will be offset by an improvement in service life
- C. The Inspector will improve job flow and schedule
- D. a) and c)
Answer: D
NEW QUESTION 32
The Inspector's Log Book is generally:
- A. Shredded by the inspector upon project completion
- B. Submitted to the client upon project completion
- C. Retained by the inspector upon project completion
- D. Shared with all parties upon project completion
Answer: C
NEW QUESTION 33
According to SSPC PA 2 a Spot Measurement is:
- A. The overall average of all readings
- B. The average of gauge readings taken in a 4cm (1.5 inch) circle
- C. The average of all spot measurements in a given area
- D. A single gauge reading
Answer: B
NEW QUESTION 34
The Inspector should record the serial numbers of inspection instruments:
- A. Only if the instrument is suspected of not working properly
- B. Only when verifying accuracy of the instrument
- C. Each time the instrument is used
- D. Only if the specification requires it
Answer: C
NEW QUESTION 35
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Metallic pathway
- C. Electrolyte
- D. Cathode
Answer: A
NEW QUESTION 36
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Hand tools
- B. Abrasive blast nozzles
- C. Airless spray equipment
- D. Power tools
Answer: D
NEW QUESTION 37
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. replica tape
- C. needle pressure gauge
- D. surface comparator
Answer: C
NEW QUESTION 38
To achieve consistently accurate results with ALL alt test equipment
- A. wear gloves when sampling.
- B. avoid placing the sample discs on a surface.
- C. calibrate the instrument in the field.
- D. wash your hands before sampling.
Answer: D
NEW QUESTION 39
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A method to grade surface profile
- B. Pass/fail criteria
- C. A final conflict resolution method
- D. A general guide
Answer: D
NEW QUESTION 40
Silicone coatings are typically:
- A. Applied in very' thin films
- B. Used as a sacrificial primer
- C. Applied in very thick films
- D. Used strictly in immersion service
Answer: A
NEW QUESTION 41
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Always handwritten
- C. Submitted before the end of the job
- D. Always typewritten
Answer: A
NEW QUESTION 42
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Purchase Professional Liability Insurance prior to job commencement
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- D. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
Answer: D
NEW QUESTION 43
If inspectors identify issues of non-conformance during an inspection, they should
- A. perform additional tests secretly to ensure there are no other potential issues at the site
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: C
NEW QUESTION 44
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. No, because there is no real difference in the standards
- B. It depends on which power tool the Contractor selects
- C. It depends on which hand tool the Contractor selects
- D. Yes, because the 'two standards are not equivalent
Answer: A
NEW QUESTION 45
Surface profile describes:
- A. The initial condition of the surface prior to abrasive blasting
- B. The level of surface cleanliness required after abrasive blasting
- C. The general condition of the surface required after abrasive blasting
- D. The level of surface roughness required after abrasive blasting
Answer: D
NEW QUESTION 46
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 47
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. develops a good anchor profile resulting in uneven coating application.
- B. develops a polished surface, which is a poor anchor profile for most coatings
- C. damages structural elements thereby speeding up the corrosion process.
- D. scratches the surface too deeply resulting in uneven coating application
Answer: B
NEW QUESTION 48
......
Pass Your NACE Exam with NACE-CIP1-001 Exam Dumps: https://www.practicematerial.com/NACE-CIP1-001-exam-materials.html
NACE-CIP1-001 Exam Dumps - NACE Practice Test Questions: https://drive.google.com/open?id=1-txgXOM3AVn_uZz7o4oPcl1Q0bA3fA5n
